Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Arcadia
Gate parts and welding in Arcadia means working on some of the heaviest, most ornate ironwork in the San Gabriel Valley. When a hinge post tilts or a weld cracks on a 600 lb custom driveway gate, you need a crew that understands how these gates were built and why they fail. We replace posts, re-hang leaves, repair rails, and weld custom brackets for homes from North Arcadia estates to the ranch houses south of Huntington Drive. Call (424) 300-8579 and a live person answers, any hour, any day.
Why Ironworks Gate Co. Is Arcadia’s Preferred Gate Parts & Welding Company
We have spent over 42 years working on gates that general contractors won’t touch. Arcadia is different from neighboring cities: the mansionization wave has left block after block of custom automated iron gates, many hung on posts and hinges originally sized for lighter work. Our crews know what happens when an 800 lb leaf meets a 1990s post footing, because we see it weekly on Foothill Boulevard, Santa Anita Avenue, and the streets running up toward the arboretum.
Victor Salinas leads our team, and he holds every job to the same standard we have kept since 1984: if it is not right, we come back and make it right. That is the 90-Day Done Right Promise, in writing, on every gate parts and welding job we complete in Arcadia. No paperwork, no arguing, no exceptions. We also carry background-checked, uniformed technicians on every visit, so the person at your gate is someone you can trust around your home.
Our Gate Parts & Welding team stocks common hinge brackets, roller bearings, post sleeves, and weld plates on our trucks, so most Arcadia repairs finish in a single visit. We know the permit desk expectations for street-facing gates in this city, and we quote the full job before a single bolt is turned.
Our Gate Parts & Welding Services in Arcadia
Hinge Replacement
Older Arcadia gates, especially on the remaining mid-century ranch homes, often hang on barrel hinges that have worn into an oval shape over 30 or 40 years. The result is a sagging leaf that scrapes the driveway and throws the operator out of alignment. We cut off the old hinges, weld in new heavy-duty ball-bearing hinges sized for the actual leaf weight, and re-hang the gate so it swings true. On North Arcadia estates with 18 ft wide driveways and dual-leaf iron gates, we typically use commercial-grade hinge assemblies rated for the load, not the light residential parts you would find at a hardware store.
Post Replacement
In Arcadia, this is the job that separates real gate specialists from everyone else. Many newer luxury homes have iron gates so heavy they tilt their own posts, especially when the original post footing was poured shallow or the post was set in a thin column of grout. We excavate the failed post, pour a deeper footing with proper rebar, set a new steel post, and weld the hinge brackets back on at the exact angle the gate needs. Our crews have done this on gated estates along Foothill Boulevard near the Santa Anita Wash and through the streets north of the 210. If the post is tilted more than a few degrees, sag correction is not optional; it is the job.
Rail Repair
Wrought iron and steel rails on Arcadia gates take constant stress from the leaf weight and from wind off the San Gabriels. A cracked rail is a safety problem and a liability, but it is also one of the most straightforward weld repairs we do. We clean the crack, bevel the edges, weld it solid, and usually add a gusset plate on the back side so the same stress point does not fail again. For rusted-through bottom rails on older estate gates, we often cut out the section and weld in a matching replacement, then grind and paint it to blend.
Custom Welding
Not every Arcadia gate needs a standard part. Some need a bracket fabricated to hold a new operator arm at the right angle. Some need a reinforced strike plate where an old latch ripped out. Some need a custom steel mount for a keypad or a photocell that sits cockeyed on a sloped driveway. We weld these on site, in the same visit, using steel matched to the existing gate. For gates that were custom-built by the original home contractor, we match the steel gauge and finish so the repair does not look like a patch.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Arcadia
We service and repair the operators most common on Arcadia driveways, including FAAC, LiftMaster, BFT, and Mighty Mule. Many North Arcadia estates run FAAC or LiftMaster Elite operators on oversize dual-leaf gates, while older homes often still have original Mighty Mule or BFT units from the 1990s and early 2000s. Our trucks carry common control boards, limit switches, gearboxes, and receiver modules, so we can diagnose and repair in one trip rather than ordering parts and coming back days later. When you call about a gate parts or welding issue in Arcadia, we bring the parts most likely to match what is on your driveway that same day.
Common Gate Parts & Welding Problems We See in Arcadia Homes
- Posts tilting under new heavy gates. The original post was fine for the wood gate installed in 1985. It was never meant for the 700 lb custom iron leaf that replaced it during a mansion rebuild. The fix is a new footing and post, not another weld on top of a failing base.
- Limit switches thrown out by Santa Ana winds. Fall wind events off the San Gabriels push oversize dual-leaf gates against their operators, stalling the motor mid-travel and stripping rack and pinion gears. We recalibrate limit cams and inspect the rack for wear on the same visit.
- Ash and grit fouling older operator housings. When wildfires burn in the foothills, fine ash settles into operator housings and circuit boards. Older FAAC and Viking units on Arcadia estates are especially prone to erratic keypad behavior and false loop detector trips after a wind event. Cleaning and board-level testing usually brings them back.
- Hinge screws ripping out of stucco or masonry posts. This is common on newer mansion builds where the gate was hung quickly and the hinges were anchored into the cosmetic column, not the structural core. We install through-bolts and welded backing plates, which hold far better than the original lag screws.
Pricing for Gate Parts & Welding in Arcadia, CA
A typical hinge replacement on a single-leaf iron gate in Arcadia runs $220 to $480, depending on leaf weight and whether we need to weld new bracket plates. Post replacement runs $650 to $1,600, with the higher end reflecting deeper footings and heavier gates on North Arcadia estates. Rail repair, including weld and gusset, usually lands between $180 and $400 per rail. Custom welding for brackets, strike plates, or keypad mounts starts around $150 and runs up to $600 for involved fabrications. Every job is quoted and agreed before we start, so the number on the invoice matches the number we gave you. We also apply our standing offers: $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% discount for seniors and veterans. Call (424) 300-8579 for a free estimate on your specific gate.
We Also Serve Cities Near Arcadia
Ironworks Gate Co. serves Arcadia and the surrounding communities, including Monrovia, Temple City, Sierra Madre, and El Monte. If your gate is in one of those cities, the same crew and the same 90-Day Done Right Promise apply. Call us and we will schedule a time that works, with the same upfront pricing and the same single-visit goal on most repairs.
Serving Arcadia, CA - Our Local Coverage Area
We’re based in the Arcadia area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Arcadia
Yes, in most cases. The FAAC 750 and 400 series control boards from that era are still serviceable, and we routinely keep them in place when the only problem is a failed hinge post or a cracked weld. The key is making sure the operator is not being overworked by a gate that sags or binds, because that is what burns out older boards. We reinforce the post, re-hang the leaf so it moves freely, and then verify the board is still sending clean signals before we leave. Call (424) 300-8579 for a free evaluation.
Because the original installer anchored the hinges into the stucco or brick cladding instead of the structural steel post inside. A 700 or 800 lb iron leaf creates enormous shear force on those hinge screws every time it swings, and surface anchors simply cannot hold. We fix this by welding backing plates to the structural post, running through-bolts, and using heavier hinge assemblies rated for the actual leaf weight. It is a permanent fix, not another lag screw that will pull out in six months. Free estimates on this repair: (424) 300-8579.
Arcadia’s building department requires permits for new gate installations and major structural changes, including replacement of a post that fronts a public right-of-way. For weld repairs and hinge replacements on an existing gate, the work is generally treated as maintenance and does not require a permit, but anything that changes the footprint, height, or opening mechanism does. We can tell you up front what your specific repair involves, and we handle the process when a permit is required. Call (424) 300-8579 and we will walk you through it.
The first thing we check is the rack itself. On older Viking operators, the nylon pinion gear wears down over time, and once it loses tooth contact with the rack, the gate will not move even though the motor runs. We also check the limit switch positions, because if the gate thinks it is already fully open or closed, it will refuse to engage. Usually the fix is a new pinion gear and a limit recalibration, often under $400. Call (424) 300-8579 for same-week service in Arcadia.
Yes. Gates installed before UL 325 safety standards were updated are often missing photo eyes or have only a single safety edge, and many older Arcadia estates still have operators that reverse too slowly or not at all. Current code requires entrapment protection on both sides of the gate and a monitored safety system on the operator. We retrofit photo eyes, safety edges, and loop detectors on older FAAC, Viking, and BFT systems regularly, usually in a single visit. Call (424) 300-8579 and we will tell you exactly what your gate needs.
Get Your Arcadia Gate Fixed Right - Call Ironworks Gate Co.
When a gate post tilts or a weld cracks, the problem only gets more expensive the longer it waits. We serve Arcadia with the same standard we have kept for over 42 years: the job done correctly, the price agreed before we start, and a written 90-Day Done Right Promise on every repair. Victor Salinas and our team answer the phone live, 24 hours a day, 7 days a week. Call (424) 300-8579 for your free estimate, and we will be there when we say.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Arcadia and the San Gabriel Valley since 1984.